This is the official manual for the Atar ST/E/Falcon Blitter. Have fun!
User Manual for the Atari ST
**** **** **** ****** ** ** ** ** ** ** ** ** **
Bit-Block Transfer Processor (BLiTTER)
TABLE OF CONTENTS
Introduction ...................................... 1 Bit-Block Transfers .......................... 2 Bit-Block Transfer ........................... 3 Functional Description ............................ 3 Programming Model ................................. 5 Register Map ................................. 5 Bit-Block Addresses .......................... 5 Source X Increment ...................... 6 Source Y Increment ...................... 6 Destination Address ..................... 6 Destination X Increment ................. 6 Destination Y Increment ................. 6 X Count ................................. 7 Y Count ................................. 7 Bit-Block Alignments ......................... 7 Endmask 1, 2, 3 ......................... 7 Skew .................................... 7 FXSR .................................... 7 NSFR .................................... 8 Logic Operations ............................. 8 Logic Operations ........................ 8 Halftone Operations .......................... 8 Halftone RAM ............................ 8 Line Number ............................. 8 Smudge .................................. 9 Halftone Operations ..................... 9 Bus Accesses ................................. 9 Hog ..................................... 9 Busy .................................... 9 Appendix A -- Programming Example ................. 10 Appendix B -- References .......................... 17
THE SCOPE OF THIS DOCUMENT is limited to a functional description of the Atari ST BLiTTER. This document is not a data sheet for system integration, rather it is a user manual for system programming. For more information, please refer to the texts listed at the end of this document.
The Atari ST Bit-Block Transfer Processor (BLiTTER) is a hardware implementation of the bit-block transfer (BitBlt) algorithm. BitBlt can be simply described as a procedure that moves bit-aligned data from a source location to a destination location through a given logic operation. The BitBlt primitive can be used to perform such operations as:
- Area seed filling
- Rotation by recursive subdivision
- Slice and smear magnification
- Brush line drawing using Bresenham DDA
- Text transformations (eg. bold, italic, outline)
- Text scrolling
- Window updating
- Pattern filling
And general memory-to-memory block copying 1.
The heart of BitBlt was first formally defined by Newman and Sproull in their description of the function RasterOp 2. As defined, RasterOp performed its block transfers on a bit-by-bit basis and was limited to a small subset of possible source and destination Boolean combinations. Enhancements to RasterOp such as processing bits in parallel or introducing a halftone pattern into the transfer were literally left as exercises for the reader.
In an effort to improve the functionality and performance of the original algorithm, the prescribed enhancements were incorporated into the definition of RasterOp and implemented in hardware as the RasterOp Chip 3. However the RasterOp Chip lacked the two-dimensionality of the original function and suffered from a performance bottleneck caused by the loading and reloading of source, destination, and halftone data (ie. it could not DMA).
While efforts were being made to improve the performance of RasterOp, the formal definition of RasterOp was further refined and became the basis of the BitBlt copyLoop primitive in the Smalltalk-80 graphics kernel 4. Because of its comprehensive interface definition, the BitBlt primitive was inefficient and required special-case optimizations that violated its general-purpose nature. Clearly a hardware solution was necessary to increase the performance of the BitBlt copyLoop without sacrificing its functionality.
The Atari ST BLiTTER is a hardware solution to the performance problems of BitBlt. The BLiTTER is a DMA device that implements the full BitBlt copyLoop definition with the addition of a few minor extensions. Single word or multi-word increments and decrements are provided for transfers to destinations in Atari ST video display memory. A center mask, which would otherwise be a constant all ones, is also provided for an additional level of texture. The remainder of this document is directly based on the original functional description of the Atari ST BLiTTER.
As previously stated, a bit-block transfer can be described as a procedure that moves bit-aligned data from a source location to a destination location through a given logic operation. There are sixteen logic combination rules associated with the merging of source and destination data. Note that this set contains all possible combinations between source and destination. The following table contains the valid BitBlt combination rules:
LOGIC OPERATIONS (~s&~d)|(~s&d)|(s&~d)|(s&d) _______________________________________ | | | MSB LSB | OP | COMBINATION RULE | | | | 0 0 0 0 | 0 | all zeros | 0 0 0 1 | 1 | source AND destination | 0 0 1 0 | 2 | source AND NOT destination | 0 0 1 1 | 3 | source | 0 1 0 0 | 4 | NOT source AND destination | 0 1 0 1 | 5 | destination | 0 1 1 0 | 6 | source XOR destination | 0 1 1 1 | 7 | source OR destination | 1 0 0 0 | 8 | NOT source AND NOT destination | 1 0 0 1 | 9 | NOT source XOR destination | 1 0 1 0 | A | NOT destination | 1 0 1 1 | B | source OR NOT destination | 1 1 0 0 | C | NOT source | 1 1 0 1 | D | NOT source OR destination | 1 1 1 0 | E | NOT source OR NOT destination | 1 1 1 1 | F | all ones | |____|__________________________________|
Adjustments to block extents and several other transfer parameters are determined prior to the invocation of the actual block transfer. These adjustments and parameters include clipping, skew, end masks, and overlap.
Clipping. The source and destination block extents are adjusted to conform with a specified clipping rectangle. Since both source and destination blocks are of equal dimension, the destination block extent is clipped to the extent of the source block (or vice versa). Note that the block transfer need not be performed if the resultant extent is zero.
Skew. The source-to-destination horizontal bit skew is calculated.
End Masks. The left and right partial word masks are determined. The masks are merged if the destination is one word in width.
Overlap. The block locations are checked for possible overlap in order to avoid the destruction of source data before it is transferred.
In non-overlapping transfers the source block scanning direction is inconsequential and can by default be from upper left to lower right. In overlapping transfers the source scanning direction is also from upper left to lower right if the source-to-destination transfer direction is up and/or to the left (ie. source address is greater than or equal to destination address). However, if the overlapping source-to-destination transfer direction is down and/or to the right (ie. source address is less than destination address), then the source data is scanned from lower right to upper left.
After the transfer parameters are determined the bit-block transfer operation can be invoked, transferring source to destination through the logic operation (HALFTONE and HOP will be described in the next section):
_________ _____________ ________________ | || | | | | SOURCE || SOURCE | | DESTINATION | |_________||_____________| |________________| |________________|<< SKEW | | | | ______________ ___|____ ________________ | | | | | | | | | HALFTONE |----| HOP |-----| LOGIC OP |--| |______________| |________| |________________| | | | ____|____ | | | | | ENDMASK |____| |_________| | _________|_________ | | | NEW DESTINATION | |___________________|
Please refer to the bit-block transfer diagram in the previous section. To understand how the components of a block transfer work, let’s look at the simplest possible transfer. Take the case where we wish to fill a block of memory with either all zeros or all ones (OP = 0 or OP = F). In this case only the LOGIC OP block, which generates the ones or zeros, and the ENDMASK block are in the data path. If the end mask contains all ones, the BLiTTER will simply write one word after the other to the destination address without ever reading the destination.
As the writes take place the destination address will be adjusted according to the values in the DESTINATION X INCREMENT, DESTINATION Y INCREMENT, X COUNT, and Y COUNT registers. These registers define the size and shape of the block to be transferred. The X and Y COUNT registers define the size of the block. The X COUNT register specifies the number of word-size writes required to update one line of the destination. The Y COUNT register specifies the number of these lines in the block. The DESTINATION X INCREMENT register is a signed (2’s complement) 16-bit quantity which is added to the destination address to calculate the address of the next destination word of the line. On the last write of the line the DESTINATION Y INCREMENT is added to calculate the address of the first word of the next line.
The end mask determines which bits of the destination word will be updated. Bits of the destination which correspond to ones in the end mask will be updated. Bits of the destination which correspond to zeros in the end mask will remain unchanged. Note that if any bits of the destination are to be left unchanged, a read-modify-write is required. In order to improve performance a read will only be performed if it is required. There are three ENDMASK registers numbered 1 through 3. ENDMASK 1 is used only for the first write of the line. ENDMASK 3 is used only for the last write of the line. ENDMASK 2 is used for all other writes.
Now let’s consider a more complicated case, suppose we want to XOR a destination block with a 16 x 16 halftone pattern. First we load the HALFTONE RAM with the halftone pattern. Select halftone only using the HOP register and select source XOR destination using the OP register. The LINE NUMBER register is used to specify which of the 16 words of HALFTONE RAM is used for the current line. This register will be incremented or decremented at the end of each line according to the sign of the DESTINATION Y INCREMENT register. Set the DESTINATION X and Y INCREMENT and X and Y COUNT registers to the appropriate values and start the transfer. This same procedure can be followed to do the combination using any logic operation by simply changing the value in the OP register. Similarly the combination can be performed using a source block instead of the HALFTONE RAM or using the logical AND of a source block and the HALFTONE RAM by changing the value of the HOP register. A source block is the same size as the destination block but may have different increments and address defined by the SOURCE X and Y INCREMENT and SOURCE ADDRESS registers.
Finally, let’s look at the case when the source and destination blocks are not bit-aligned. In this case we may need to read the first two source words into the 32-bit source buffer and use the 16 bits that line up with the appropriate bits of the destination, as specified by the SKEW register. When the next source word is read, the lower 16 bits of the source buffer is transferred to the upper 16 bits and the lower is replaced by the new data. This process is reversed when the source is being read from the right to the left (SOURCE X INCREMENT negative). Since there are cases when it may be necessary for an extra source read to be performed at the beginning of each line to “prime” the source buffer and cases when it may not be necessary due to the choice of end mask, a bit has been provided which forces the extra read. The FXSR (aka. pre-fetch) bit in the SKEW register indicates, when set, that an extra source read should be performed at the beginning of each line to “prime” the source buffer. Similarly the NFSR (aka post-flush) bit, when set, will prevent the last source read of the line. This read may not be necessary with certain combinations of end masks and skews. If the read is suppressed, the lower to upper half buffer transfer still occurs. Also in this case, a readmodify-write cycle is performed on the destination for the last write of each line regardless of the value of the corresponding ENDMASK register.
The BLiTTER contains a set of registers that specify bit-block addresses, bit-block alignments, logic and halftone operations, and bus accesses. The register set-up time remains practically constant and is large relative to small block transfers, whereas large bit-blocks are dominated by the execution time of the transfer itself.
The following is a map of the BLiTTER programmable registers (note that all unused bits read back as zeros):
FF 8A00 |oooooooo||oooooooo| HALFTONE RAM FF 8A02 |oooooooo||oooooooo| FF 8A04 |oooooooo||oooooooo| : :: : FF 8A1E |oooooooo||oooooooo| FF 8A20 |oooooooo||ooooooo-| SOURCE X INCREMENT FF 8A22 |oooooooo||ooooooo-| SOURCE Y INCREMENT FF 8A24 |--------||oooooooo| SOURCE ADDRESS FF 8A26 |oooooooo||ooooooo-| FF 8A28 |oooooooo||oooooooo| ENDMASK 1 FF 8A2A |oooooooo||oooooooo| ENDMASK 2 FF 8A2C |oooooooo||oooooooo| ENDMASK 3 FF 8A2E |oooooooo||ooooooo-| DESTINATION X INCREMENT FF 8A30 |oooooooo||ooooooo-| DESTINATION Y INCREMENT FF 8A32 |--------||oooooooo| DESTINATION ADDRESS FF 8A34 |oooooooo||ooooooo-| FF 8A36 |oooooooo||oooooooo| X COUNT FF 8A38 |oooooooo||oooooooo| Y COUNT FF 8A3A |------oo| HOP FF 8A3B |----oooo| OP FF 8A3C |ooo-oooo| ||| |__|_____________ LINE NUMBER |||__________________ SMUDGE ||__________________ HOG |___________________ BUSY FF 8A3D |oo--oooo| || |__|_____________ SKEW ||___________________ NFSR |____________________ FXSR
This subsection describes registers that specify bit-block origins, address increments, and extents.
This 23-bit register contains the current address of the source field (only word addresses may be specified). It may be accessed using either word or longword instructions. The value read back is always the address of the next word to be used in a source operation. It will be updated by the amounts specified in the SOURCE X INCREMENT and the SOURCE Y INCREMENT registers as the transfer progresses.
SOURCE X INCREMENT
This is a signed 15-bit register, the least significant bit is ignored, specifying the offset in bytes to the address of the next source word in the current line. This value will be sign-extended and added to the SOURCE ADDRESS register at the end of a source word fetch, whenever the X COUNT register does not contain a value of one. If the X COUNT register is loaded with a value of one this register is not used. Byte instructions can not be used to read or write this register.
SOURCE Y INCREMENT
This is a signed 15-bit register, the least significant bit is ignored, specifying the offset in bytes to the address of the first source word in the next line. This value will be sign-extended and added to the SOURCE ADDRESS register at the end of the last source word fetch of each line (when the X COUNT register contains a value of one). If the X COUNT register is loaded with a value of one this register is used exclusively. Byte instructions can not be used to read or write this register.
This 23-bit register contains the current address of the destination field (only word addresses may be specified). It may be accessed using either word or long-word instructions. The value read back is always the address of the next word to be modified in the destination field. It will be updated by the amounts specified in the DESTINATION X INCREMENT and the DESTINATION Y INCREMENT registers as the transfer progresses.
DESTINATION X INCREMENT
This is a signed 15-bit register, the least significant bit is ignored, specifying the offset in bytes to the address of the next destination word in the current line. This value will be sign-extended and added to the DESTINATION ADDRESS register at the end of a destination word write, whenever the X COUNT register does not contain a value of one. If the X COUNT register is loaded with a value of one this register is not used. Byte instructions can not be used to read or write this register.
DESTINATION Y INCREMENT
This is a signed 15-bit register, the least significant bit is ignored, specifying the offset in bytes to the address of the first destination word in the next line. This value will be sign-extended and added to the DESTINATION ADDRESS register at the end of the last destination word write of each line (when the X COUNT register contains a value of one). If the X COUNT register is loaded with a value of one this register is used exclusively. Byte instructions cannot be used on this register.
This 16-bit register specifies the number of words contained in one destination line. The minimum number is one and the maximum is 65536 designated by zero. Byte instructions can not be used to read or write this register. Reading this register returns the number of destination words yet to be written in the current line, NOT necessarily the value initially written to the register. Each time a destination word is written the value will be decremented until it reaches zero, at which time it will be returned to its initial value.
This 16-bit register specifies the number of lines in the destination field. The minimum number is one and the maximum is 65536 designated by zero. Byte instructions can not be used to read or write this register. Reading this register returns the number of destination lines yet to be written, NOT necessarily the value initially written to the register. Each time a destination line is completed the value will be decremented until it reaches zero, at which time the tranfer is complete.
This subsection describes registers that specify bit-block end masks, source-to-destination skew, and source data fetching.
ENDMASK 1, 2, 3
These 16-bit registers are used to mask destination writes. Bits of the destination word which correspond to ones in the current ENDMASK register will be modified. Bits of the destination word which correspond to zeros in the current ENDMASK register will remain unchanged. The current ENDMASK register is determined by position in the line. ENDMASK 1 is used only for the first write of a line. ENDMASK 3 is used only for the last write of a line. ENDMASK 2 is used in all other cases. In the case of a one word line ENDMASK 1 is used. Byte instructions can not be used to read or write these registers.
The least significant four bits of the byte-wide register at FF 8A3D specify the source skew. This is the amount the data in the source data latch is shifted right before being combined with the halftone mask and destination data.
FXSR stands for Force eXtra Source Read. When this bit is set one extra source read is performed at the start of each line to initialize the remainder portion source data latch.
NFSR stands for No Final Source Read. When this bit is set the last source read of each line is not performed. Note that use of this and/or the FXSR bit the requires an adjustment to the SOURCE Y INCREMENT and SOURCE ADDRESS registers.
This subsection describes registers that specify the logic combinations of source and destination bit-block data.
The least significant four bits of the byte-wide register at FF 8A3B specify the source/destination combination rule according to the following table:
_______________________________________ | | | | OP | COMBINATION RULE | | | | | 0 | all zeros | | 1 | source AND destination | | 2 | source AND NOT destination | | 3 | source | | 4 | NOT source AND destination | | 5 | destination | | 6 | source XOR destination | | 7 | source OR destination | | 8 | NOT source AND NOT destination | | 9 | NOT source XOR destination | | A | NOT destination | | B | source OR NOT destination | | C | NOT source | | D | NOT source OR destination | | E | NOT source OR NOT destination | | F | all ones | |____|__________________________________|
This subsection describes registers that specify the halftone pattern memory, halftone word index, and combinations of source and halftone data.
This RAM holds a 16x16 halftone pattern mask. Each word is valid for one line of the destination field and is repeated every 16 lines. The current word is pointed to by the value in the LINE NUMBER register. These registers may be read, but can not be accessed using byte-wide instructions.
The least significant four bits of the byte-wide register at FF 8A3C specify the current halftone mask. The current value times two plus FF 8A00 gives the address of the current halftone mask. This value is incremented or decremented at the end of each line and will wrap through zero. The sign of the DESTINATION Y INCREMENT determines if the line number is incremented or decremented (increment if positive, decrement if negative).
The SMUDGE bit, when set, causes the least significant four bits of the skewed source data to be used as the address of the current halftone pattern. Note that the halftone operation is still valid when SMUDGE is set.
The least significant two bits of the byte-wide register at FF 8A3A specify the source/halftone combination rule according to the following table:
_____________________________ | | | | HOP| COMBINATION RULE | | | | | 0 | all ones | | 1 | halftone | | 2 | source | | 3 | source AND halftone | |____|________________________|
This subsection describes registers that specify bus access control and BLiTTER start/status.
The HOG bit, when cleared, causes the processor and the blitter to share the bus equally. In this mode each will get 64 bus cycles while the other is halted. When set, the bit will cause the processor to be halted until the transfer is complete. In either case the BLiTTER will yield to other DMA devices. Bus arbitration may allow the processor to execute one or more instructions even in hog mode. Therefore, don’t assume that the instruction following the one which sets the BUSY bit will be executed only after the transfer is complete. The BUSY bit may be polled to achieve this kind of synchronization.
The BUSY bit is set after all the other registers have been initialized to begin the transfer operation. It will remain set until the transfer is complete. The interrupt line is a duplicate of this bit. See the Programming Example for more details on how to use the BUSY bit.
Appendix A – Programming Example
In order to maintain software compatibility with new or upgraded Atari STs equipped with the BLiTTER, software developers need only follow guidelines set forth by the VDI and “LINE A” documents. Revised TOS ROMs will work in concert with the BLiTTER, enhancing the performance of many VDI and “LINE A” operations. This occurs in a manner transparent to an executing program. Thus no special actions need be taken to utilize the performance advantages of the BLiTTER.
As a rule of thumb, never make a VDI or “LINE A” call from within an interrupt context since unpredictable and potentially catastrophic results will occur should one BLiTTER operation interrupt another BLiTTER operation.
The following program has not been optimized and is presented here for exemplary purposes only.
* (c) 1987 Atari Corporation * All Rights Reserved. * BLiTTER BASE ADDRESS BLiTTER equ $FF8A00 * BLiTTER REGISTER OFFSETS Halftone equ 0 Src_Xinc equ 32 Src_Yinc equ 34 Src_Addr equ 36 Endmask1 equ 40 Endmask2 equ 42 Endmask3 equ 44 Dst_Xinc equ 46 Dst_Yinc equ 48 Dst_Addr equ 50 X_Count equ 54 Y_Count equ 56 HOP equ 58 OP equ 59 Line_Num equ 60 Skew equ 61 * BLiTTER REGISTER FLAGS fHOP_Source equ 1 fHOP_Halftone equ 0 fSkewFXSR equ 7 fSkewNFSR equ 6 fLineBusy equ 7 fLineHog equ 6 fLineSmudge equ 5 * BLiTTER REGISTER MASKS mHOP_Source equ $02 mHOP_Halftone equ $01 mSkewFXSR equ $80 mSkewNFSR equ $40 mLineBusy equ $80 mLineHog equ $40 mLineSmudge equ $20 * E n D m A s K d A t A * * These tables are referenced by PC relative instructions. Thus, * the labels on these tables must remain within 128 bytes of the * referencing instructions forever. Amen. * * 0: Destination 1: Source <<< Invert right end mask data >>> lf_endmask: dc.w $FFFF rt_endmask: dc.w $7FFF dc.w $3FFF dc.w $1FFF dc.w $0FFF dc.w $07FF dc.w $03FF dc.w $01FF dc.w $00FF dc.w $007F dc.w $003F dc.w $001F dc.w $000F dc.w $0007 dc.w $0003 dc.w $0001 dc.w $0000 * TiTLE: BLiT_iT * * PuRPoSE: * Transfer a rectangular block of pixels located at an * arbitrary X,Y position in the source memory form to * another arbitrary X,Y position in the destination memory * form using replace mode (boolean operator 3). * The source and destination rectangles should not overlap. * * iN: * a4 pointer to 34 byte input parameter block * * Note: This routine must be executed in supervisor mode as * access is made to hardware registers in the protected region * of the memory map. * * * I n p u t p a r a m e t e r b l o c k o f f s e t s SRC_FORM equ 0 ; Base address of source memory form .l SRC_NXWD equ 4 ; Offset between words in source plane .w SRC_NXLN equ 6 ; Source form width .w SRC_NXPL equ 8 ; Offset between source planes .w SRC_XMIN equ 10 ; Source blt rectangle minimum X .w SRC_YMIN equ 12 ; Source blt rectangle minimum Y .w DST_FORM equ 14 ; Base address of destination memory form .l DST_NXWD equ 18 ; Offset between words in destination plane.w DST_NXLN equ 20 ; Destination form width .w DST_NXPL equ 22 ; Offset between destination planes .w DST_XMIN equ 24 ; Destination blt rectangle minimum X .w DST_YMIN equ 26 ; Destination blt rectangle minimum Y .w WIDTH equ 28 ; Width of blt rectangle .w HEIGHT equ 30 ; Height of blt rectangle .w PLANES equ 32 ; Number of planes to blt .w BLiT_iT: lea BLiTTER,a5 ; a5-> BLiTTER register block * * Calculate Xmax coordinates from Xmin coordinates and width * move.w WIDTH(a4),d6 subq.w #1,d6 ; d6<- width-1 move.w SRC_XMIN(a4),d0 ; d0<- src Xmin move.w d0,d1 add.w d6,d1 ; d1<- src Xmax=src Xmin+width-1 move.w DST_XMIN(a4),d2 ; d2<- dst Xmin move.w d2,d3 add.w d6,d3 ; d3<- dst Xmax=dstXmin+width-1 * * Endmasks are derived from source Xmin mod 16 and source Xmax * mod 16 * moveq.l #$0F,d6 ; d6<- mod 16 mask move.w d2,d4 ; d4<- DST_XMIN and.w d6,d4 ; d4<- DST_XMIN mod 16 add.w d4,d4 ; d4<- offset into left end mask tbl move.w lf_endmask(pc,d4.w),d4 ; d4<- left endmask move.w d3,d5 ; d5<- DST_XMAX and.w d6,d5 ; d5<- DST_XMAX mod 16 add.w d5,d5 ; d5<- offset into right end mask tbl move.w rt_endmask(pc,d5.w),d5 ; d5<-inverted right end mask not.w d5 ; d5<- right end mask * * Skew value is (destination Xmin mod 16 - source Xmin mod 16) * && 0x000F. Three discriminators are used to determine the * states of FXSR and NFSR flags: * * bit 0 0: Source Xmin mod 16 =< Destination Xmin mod 16 * 1: Source Xmin mod 16 > Destination Xmin mod 16 * * bit 1 0: SrcXmax/16-SrcXmin/16 <> DstXmax/16-DstXmin/16 * Source span Destination span * 1: SrcXmax/16-SrcXmin/16 == DstXmax/16-DstXmin/16 * * bit 2 0: multiple word Destination span * 1: single word Destination span * * These flags form an offset into a skew flag table yielding * correct FXSR and NFSR flag states for the given source and * destination alignments * move.w d2,d7 ; d7<- Dst Xmin and.w d6,d7 ; d7<- Dst Xmin mod16 and.w d0,d6 ; d6<- Src Xmin mod16 sub.w d6,d7 ; d7<- Dst Xmin mod16-Src Xmin mod16 * ; if Sx&F > Dx&F then cy:1 else cy:0 clr.w d6 ; d6<- initial skew flag table index addx.w d6,d6 ; d6[bit0]<- intraword alignment flag lsr.w #4,d0 ; d0<- word offset to src Xmin lsr.w #4,d1 ; d1<- word offset to src Xmax sub.w d0,d1 ; d1<- Src span - 1 lsr.w #4,d2 ; d2<- word offset to dst Xmin lsr.w #4,d3 ; d3<- word offset to dst Xmax sub.w d2,d3 ; d3<- Dst span - 1 bne set_endmasks ; 2nd discriminator is one word dst * When destination spans a single word, both end masks are merged * into Endmask1. The other end masks will be ignored by the BLiTTER and.w d5,d4 ; d4<- single word end mask addq.w #4,d6 ; d6[bit2]:1 => single word dst set_endmasks: move.w d4,Endmask1(a5) ; left end mask move.w #$FFFF,Endmask2(a5) ; center end mask move.w d5,Endmask3(a5) ; right end mask cmp.w d1,d3 ; the last discriminator is the bne set_count ; equality of src and dst spans addq.w #2,d6 ; d6[bit1]:1 => equal spans set_count: move.w d3,d4 addq.w #1,d4 ; d4<- number of words in dst line move.w d4,X_Count(a5) ; set value in BLiTTER * Calculate Source starting address: * * Source Form address + * (Source Ymin * Source Form Width) + * ((Source Xmin/16) * Source Xinc) move.l SRC_FORM(a4),a0 ; a0-> start of Src form move.w SRC_YMIN(a4),d4 ; d4<- offset in lines to Src Ymin move.w SRC_NXLN(a4),d5 ; d5<- length of Src form line mulu d5,d4 ; d4<- byte offset to (0, Ymin) add.l d4,a0 ; a0-> (0, Ymin) move.w SRC_NXWD(a4),d4; d4<- offset between consecutive move.w d4,Src_Xinc(a5) ; words in Src plane mulu d4,d0 ; d0<- offset to word containing Xmin add.l d0,a0 ; a0-> 1st src word (Xmin, Ymin) * Src_Yinc is the offset in bytes from the last word of one Source * line to the first word of the next Source line mulu d4,d1 ; d1<- width of src line in bytes sub.w d1,d5 ; d5<- value added to ptr at end move.w d5,Src_Yinc(a5) ; of line to reach start of next * Calculate Destination starting address move.l DST_FORM(a4),a1 ; a1-> start of dst form move.w DST_YMIN(a4),d4 ; d4<- offset in lines to dst Ymin move.w DST_NXLN(a4),d5 ; d5<- width of dst form mulu d5,d4 ; d4<- byte offset to (0, Ymin) add.l d4,a1 ; a1-> dst (0, Ymin) move.w DST_NXWD(a4),d4 ; d4<- offset between consecutive move.w d4,Dst_Xinc(a5) ; words in dst plane mulu d4,d2 ; d2<- DST_NXWD * (DST_XMIN/16) add.l d2,a1 ; a1-> 1st dst word (Xmin, Ymin) * Calculate Destination Yinc mulu d4,d3 ; d3<- width of dst line - DST_NXWD sub.w d3,d5 ; d5<- value added to dst ptr at move.w d5,Dst_Yinc(a5) ; end of line to reach next line * The low nibble of the difference in Source and Destination alignment * is the skew value. Use the skew flag index to reference FXSR and * NFSR states in skew flag table. and.b #$0F,d7 ; d7<- isolated skew count or.b skew_flags(pc,d6.w),d7 ; d7<- necessary flags and skew move.b d7,Skew(a5) ; load Skew register move.b #mHOP_Source,HOP(a5) ; set HOP to source only move.b #3,OP(a5) ; set OP to "replace" mode lea Line_Num(a5),a2 ; fast refer to Line_Num register move.b #fLineBusy,d2 ; fast refer to LineBusy flag move.w PLANES(a4),d7 ; d7 <- plane counter bra begin * T h e s e t t i n g o f s k e w f l a g s * * * QUALIFIERS ACTIONS BITBLT DIRECTION: LEFT -> RIGHT * * equal Sx&F> * spans Dx&F FXSR NFSR * * 0 0 0 1 |..ssssssssssssss|ssssssssssssss..| * |......dddddddddd|dddddddddddddddd|dd..............| * * 0 1 1 0 |..dddddddddddddd|dddddddddddddd..| * |......ssssssssss|ssssssssssssssss|ss..............| * * 1 0 0 0 |..ssssssssssssss|ssssssssssssss..| * |...ddddddddddddd|ddddddddddddddd.| * * 1 1 1 1 |...sssssssssssss|sssssssssssssss.| * |..dddddddddddddd|dddddddddddddd..| skew_flags: dc.b mSkewNFSR ; Source span < Destination span dc.b mSkewFXSR ; Source span > Destination span dc.b 0 ; Spans equal Shift Source right dc.b mSkewNFSR+mSkewFXSR ; Spans equal Shift Source left * When Destination span is but a single word ... dc.b 0 ; Implies a Source span of no words dc.b mSkewFXSR ; Source span of two words dc.b 0 ; Skew flags aren't set if Source and dc.b 0 ; Destination spans are both one word next_plane: move.l a0,Src_Addr(a5) ; load Source pointer to this plane move.l a1,Dst_Addr(a5) ; load Dest ptr to this plane move.w HEIGHT(a4),Y_Count(a5) ; load the line count move.b #mLineBusy,(a2) ; <<< start the BLiTTER >>> add.w SRC_NXPL(a4),a0 ; a0-> start of next src plane add.w DST_NXPL(a4),a1 ; a1-> start of next dst plane * The BLiTTER is usually operated with the HOG flag cleared. * In this mode the BLiTTER and the ST's cpu share the bus equally, * each taking 64 bus cycles while the other is halted. This mode * allows interrupts to be fielded by the cpu while an extensive * BitBlt is being processed by the BLiTTER. There is a drawback in * that BitBlts in this shared mode may take twice as long as BitBlts * executed in hog mode. Ninety percent of hog mode performance is * achieved while retaining robust interrupt handling via a method * of prematurely restarting the BLiTTER. When control is returned * to the cpu by the BLiTTER, the cpu immediately resets the BUSY * flag, restarting the BLiTTER after just 7 bus cycles rather than * after the usual 64 cycles. Interrupts pending will be serviced * before the restart code regains control. If the BUSY flag is * reset when the Y_Count is zero, the flag will remain clear * indicating BLiTTER completion and the BLiTTER won't be restarted. * * (Interrupt service routines may explicitly halt the BLiTTER * during execution time critical sections by clearing the BUSY flag. * The original BUSY flag state must be restored however, before * termination of the interrupt service routine.) restart: bset.b d2,(a2) ; Restart BLiTTER and test the BUSY nop ; flag state. The "nop" is executed bne restart ; prior to the BLiTTER restarting. * ; Quit if the BUSY flag was clear. begin: dbra d7,next_plane rts
Appendix B – References
Course Notes: Bitmap Graphics’, AT&T Bell Laboratories 1984.
Interactive Computer Graphics’, McGraw-Hill 1979, Chapter 18.
Compilers 1984. See also ‘VL16160 RasterOp Graphics/Boolean Operation ALU’, VLSI Technology 1986.
Language and its Implementation’, Addison-Wesley 1983, Chapter 18.
Appendix C – Blitter Execution Times
Blitter Execution Times
| HOP LOP| 0 1 2 3 HOP = Halftone Operation ---+----------- LOP = Logical Operation 0 | 1 1 1 1 1 | 2 2 3 3 All timings are assuming the BLITTER is 2 | 2 2 3 3 the only DMA device using the BUS. If other 3 | 1 1 2 2 devices are using the BUS the figures may 4 | 2 2 3 3 increase. 5 | 2 2 2 2 6 | 2 2 3 3 All timing figures are given in nops per word 7 | 2 2 3 3 of transfer. Ie. a value of 2 would take the 8 | 2 2 3 3 equivilent time of 2 nops to transfer 1 word 9 | 2 2 3 3 of data. 10 | 2 2 2 2 11 | 2 2 3 3 12 | 1 1 2 2 13 | 2 2 3 3 14 | 2 2 3 3 15 | 1 1 1 1